It looks like you're new here. If you want to get involved, click one of these buttons!
Subscribe to our Patreon, and get image uploads with no ads on the site!
Base theme by DesignModo & ported to Powered by Vanilla by Chris Ireland, modified by the "theFB" team.
Comments
The Underdrive was a Mad Professor pedal.
Can be done with any good EQ pedal.
https://speakerimpedance.co.uk/?act=two_parallel&page=calculator
"Take these three items, some WD-40, a vise grip, and a roll of duct tape. Any man worth his salt can fix almost any problem with this stuff alone." - Walt Kowalski
"Only two things are infinite - the universe, and human stupidity. And I'm not sure about the universe." - Albert Einstein
now I’m torn between buying the EQ200 which I don’t really need right now as I’m stuck at home and the LS2 which I also don’t really need right now.
If you can't find a second hand EQ200, there's the older EQ-20. There are two in the shop I work for, but unfortunately they're closed at the moment...
"Take these three items, some WD-40, a vise grip, and a roll of duct tape. Any man worth his salt can fix almost any problem with this stuff alone." - Walt Kowalski
"Only two things are infinite - the universe, and human stupidity. And I'm not sure about the universe." - Albert Einstein
and it’s quite cheap.
I think I’ll do that for now!
thanks
Connect the guitar to the pedal input, the B send to the amp's input, the B return to the amp's FX send, and the pedal's output to the amp's FX return. Select A-B on the Mode, not bypass. Essentially you're then running the amp's overdrive section as a "pedal" in the B loop. I would set the B loop level to the centre - that way it won't affect the range of the controls on the amp. The A level should then give you enough boost to match the amp's volume.
You can then also run different effects in the loops - if for example you only want chorus or reverb on your clean sound not the overdrive, just put the chorus/reverb pedal in the A loop.
I should probably mention that I've never actually done it on a Jubilee . Just on a couple of other amps with this problem - but I'm sure it will work.
"Take these three items, some WD-40, a vise grip, and a roll of duct tape. Any man worth his salt can fix almost any problem with this stuff alone." - Walt Kowalski
"Only two things are infinite - the universe, and human stupidity. And I'm not sure about the universe." - Albert Einstein
I'm eagerly awaiting the lovely people at Hermes to drop me a Mini Jubilee, and from what I have read, I'm anticipating similar issues with clean / dirt balance... which might be a problem if I ever get to play a gig again!!
musteatbrain... how did the LS2 solution work out for you? I'm not sure I've 100% understood. Are you bypassing the preamp completely for clean, or just dropping the level in front, then boosting again in the loop?
http://www.thefretboard.co.uk/discussion/57632/
I’ve stopped using it that way though as I stumbled on a setup I like more.
It can’t be used to lower the signal going in to the preamp whilst boosting in the loop unfortunately.
I now usually have a very simple arrangement:
P between 4 and 6 based on the guitar
B 8.5
M 6
T between 2 and 4 based on the guitar
G 6
Clean channel sometimes gets a clean boost in the loop.
Lead channel gets a juansolo modded tubescreamer.
gain at noon, volume at 3 o’clock tone at 9 o’clock.
This makes a similar sound to the gain of the amp being on 8 but it feedsback a little sooner, with the compromise of a little hiss.
I tend to use single coils on the clean channel and humbuckers for the lead. I almost never use the rhythm clip.
this is the most balanced setup I can find with my setup of guitars and speakers.
I’m writing this in so much detail as a reminder to myself as well, because my one year old loves to set the dials on it.
The settings I use are actually based from a video on how John Frusciante uses his on the clean channel.